> >>SebArt Avanti XS 120mm Jet 1.9m + JP Hobby 120mm 12S (White/Blue/Gold) PNP (with retracts)
SebArt Avanti XS 120mm Jet 1.9m + JP Hobby 120mm 12S (White/Blue/Gold) PNP (with retracts) View larger
Previous Next

SebArt Avanti XS 120mm Jet 1.9m + JP Hobby 120mm 12S (White/Blue/Gold) PNP (with retracts)

SEB-A190-WB+JPH12S

New product

Sebart

Combo with EDF 12-blades 120mm JP Hobby V2 100% metal with motor 12S 760Kv and ECS 160A + Ubec 12A. The Avanti XS, with a wingspan of 1.80m is designed with a fiberglass fuselage painted after demolding, wings and stabilizers with Oracover and the electric retractable landing gear equipped with brakes, the traps, their three servos and the sequencer traps are already installed.

More details

Available on order

By buying this product you can collect up to 2257 points . Your cart will total 2257 points that can be converted into a voucher of US $53.27 .


US $2,663.85

Instead of US $2,926.20

Accessories and other versions

Data sheet

Type of kit: PNP
Wingspan (mm): 1800mm / 70.86in
Length (mm): 1900mm / 74.80in
Flying weight (gr) 8.5kg with an EDF 120mm + battery
CG (Center of Gravity) Check manual
Servos 6 MG mini servos + 2 standard for flaps
Servo Size: Mini, Standard
EDF thrust (categorization) 6-8kg
Direction of Rotation (EDF Rotor) Classic Counter Clock Wize (CCW)
EDF Diameter Class (mm): 120
EDF Outside Diameter (mm): 123 mm
Blades: 12
Turbine shroud Metal
EDF Rotor Metal
Power System JP 5050-Ⅵ
No. of Magnet Poles: 12
Turns/min/Volt (Kv): 760 Kv
Motor Type: Out-Runner
Motor Diameter (mm): 50
Shaft diameter (mm): 8
Max Intensity (A): 130A
Battery Cells: 12s - 44.4v
Battery Capacity (mAh) 5.000 mAh, 5.800 mAh
Connection: Pk 5mm
Surfaces Ailerons, Rudder, Elevator, Flaps
Landing Gear Retractable suspended gear
Material Wood, Oracover wings coverage, Fiberglass
Build time 12 hours
Required Radio Minimum 7 channels
Recommended pilot skill level Advanced, Intermediate

More info

SebArt Avanti XS 120mm Jet 1.9m + JP Hobby 120mm 12S (White/Blue/Gold) PNP (with retracts)

Combo with EDF 12-blades 120mm JP Hobby V2 100% metal with motor 12S 760Kv and ECS 160A + Ubec 12A

Like its little brother, the Avanti XS, with a wingspan of 1.80m and a length of 1.90m, is designed in the same way, namely a fuselage fiberglass painted after demolding, wings and stabilizers with Oracover and the electric retractable landing gear equipped with brakes, the traps, their three servos and the sequencer traps are already installed.

As the all other products of the brand, the construction and the finish are of irreproachable quality. This model is intended for a 120mm EDF turbine. Its weight in flight in EDF version equipped with a 12S 5800mAh battery (2x 6S) is 8.5kg.

Characteristics

  • Wing Span: 1800mm / 70.86in
  • Length: 1900mm / 74.80in
  • 8.5kg flying weight with an EDF 120mm + battery
  • All parts of the fuselage are fiber
  • Wings and Stabilizer in Oracover

Included in the kit

  • SebArt Avanti XS 120mm Jet 1.9m
  • EDF JP Hobby 120mm 12 blades V2 
  • Motor 12S 760Kv
  • ECS 160A brushless
  • UBEC 12A
  • Electric Retractable Landing Gear
  • All hardware and all plastic parts needed to assemble the kit
  • Cockpit and canopy
  • Decals
  • Detailed illustrated instructions

Not included

  • Radio 7 ch. minimum 
  • 6x MG minis servos + 2 standard servos for flaps
  • Battery: 2x 6S 5000-5800mAh LiPo(EDF version)

EDF Ducted Fan JP HOBBY 120mm 12 blades + 12S Motor 760Kv

100% CNC aluminium JP Hobby EDF unit (shroud and rotor) for 12s

Description

  • Jingpin Hobby uses High grade aluminium alloy material for highest rigid structure and lightest weight.
  • The shroud acts as a heat sink, removing heat from the motor. This design creates a more efficiently running motor and will provide peak performance while extending the lifespan of the motor.
  • The highly rigid structure design is capable of running up to high RPM to produce extremely high efflux velocity for maximum speed and efficiency.
  • Anti Blade flying out design,the Blades be safety kept in the shroud and without damage.It is the best replacement for your plastic or carbon shroud if you want to have a safety EDF fan.
  • Each metal blade is precisely made of High Grade Aluminum alloy to generate jet airflow. Every blade has been tested for 8 hours of metal fatigue test as well as in the dynamic balance machine for calibration, making it bring a better and safer user experience for every RC fan.
  • You could assemble our EDF system with any other motor without losing dynamic balance effect.

The motor and fan unit comes assembled and balanced from the factory.

Measures

About the above measures : they have been read on the test bench with the intake lip on the unit. The measures have been made using a bench stabilized power source. Results may changed depening upon your equipment and situation.

 Description / LiPo    12s (44.4v)   12s (48.0v)  
 Thrust: 7.5 kg   8.62 kg 
 Current: 112 A 127 A
 Power: 4972 W 6096 W
 Recommended ESC:    120 A / HV  150 A / HV 
 Recommended battery:    5000mAh 40C    5000mAh 40C 

 
The controller should be chosen 20% over rated due to the long lasting load.
LV = low voltage controler up to 6s, HV = high voltage controler above 6s.
Battery should be chosen about 15/ - 1/20 of the max current for 4-3 minutes WOT. 30-40 C is appropriate.
Operating the motor outside of the specifications listed above can either damage the motor, battery or esc. It is important that these components are set up properly. Failure to do so can void the warranty. It is strongly encouraged to use a Watt Meter to test the watt and amp performance when setting up a new system. If the output is above the factory recommended specs, then it needs to be adjusted by the esc. The timing and throttle settings on the esc can help to set the appropriate levels.

Specifications

  • Special high grade aluminum quality
  • Motor Kv: 760
  • Motor: MT-5050-12S (8mm axle) Outrunner 12 poles
  • Motor diameter: 42mm
  • Motor length: 50mm
  • Rotor: 120mm 12 blades aluminium
  • External diameter: 123mm
  • Internal diameter: 120mm
  • Inlet ring diameter: 136mm (removable)
  • Ejection diameter: 120 mm
  • Combo max thrust: 8.62Kg
  • Weight: 693g (combo EDF + lip + motor )
  • Max efficiency: 90 %
  • Recommended max. rotation speed: 82000
  • Speed Control Advanced Timing Setting: 15° and under
  • Connections: Banana / PK 5mm (in place)

Content

  • 1x JP Hobby 12s 120mm full metal EDF unit
  • Connectors
WARNING: This turbine is delivered with the engine cover shown in the pictures. This engine cover significantly improves the flow of ejected air without this improvement can be considered an improvement in performance of the turbine. On the other hand, the engine cover significantly reduces engine ventilation and may in some cases cause it to overheat. We advise you not to use the engine cover or to check that the engine temperature is not excessive after a flight.

Instruction manuals

 
 
 
  • Reviews

    • No customer reviews for the moment.

    Write a review

    SebArt Avanti XS 120mm Jet 1.9m + JP Hobby 120mm 12S (White/Blue/Gold) PNP (with retracts)

    SebArt Avanti XS 120mm Jet 1.9m + JP Hobby 120mm 12S (White/Blue/Gold) PNP (with retracts)

    Combo with EDF 12-blades 120mm JP Hobby V2 100% metal with motor 12S 760Kv and ECS 160A + Ubec 12A. The Avanti XS, with a wingspan of 1.80m is designed with a fiberglass fuselage painted after demolding, wings and stabilizers with Oracover and the electric retractable landing gear equipped with brakes, the traps, their three servos and the sequencer traps are already installed.

    Download

    SEBART Avanti XS 1.9m Manual EN

    Download (118.55k)

    30 other products in the same category:

    My account

    Information

    © Copyright 2024 TURBINES RC. All Rights Reserved.

    Newsletter

    Follow us

    This website uses its own and third-party cookies to improve our services and show you advertising related to your preferences by analyzing your browsing habits. To give your consent to its use, press the Accept button.

    More information Customize cookies

    Cookie preferences
    Consent

    Functional cookies
    No
    Yes
    Functional cookies are strictly necessary to provide the services of the shop, as well as for its proper functioning, so it is not possible to refuse their use. They allow the user to browse through our website and use the different options or services that exist on it.
    Cookie Provider Purpose Expiry
    PHP_SESSID www.turbines-rc.com The PHPSESSID cookie is native to PHP and allows websites to store serialised status data. On the website it is used to establish a user session and to pass state data through a temporary cookie, which is commonly known as a session cookie. These Cookies will only remain on your computer until you close your browser. Session
    PrestaShop-# www.turbines-rc.com This is a cookie used by Prestashop to store information and keep the user's session open. It stores information such as currency, language, customer ID, among other data necessary for the proper functioning of the shop. 480 hours
    Analytics cookies
    No
    Yes
    Collect information about the user's browsing experience in the shop, usually anonymously, although sometimes they also allow the user to be uniquely and unequivocally identified in order to obtain reports on the user's interests in the products or services offered by the shop.
    Cookie Provider Purpose Expiry
    _ga Google Registers a unique ID that is used to generate statistical data on how the visitor uses the website. 2 years
    _gat Google Used by Google Analytics to throttle request rate 1 day
    _gat_gtag_UA_# Google Used to throttle request rate. 1 minute
    _gd# Google This is a Google Analytics Session cookie used to generate statistical data on how you use the website which is removed when you quit your browser. Session
    _gid Google Registers a unique ID that is used to generate statistical data on how the visitor uses the website. 1 day